STANDARD HAVEN SPAS PARAMOUNT SPASIDE CONTROL PANEL
IMPORTANT NOTE: Some keys have two different functions. One is for the "normal mode" and the other is for the "programming mode"
PUMP 1 KEY: Pump 1 is a two-speed pump,
the Pump1 key is used to turn it on and to select between off, low and high
speeds. A built-in tier will shut the pump off 20 minutes after it has been
started unless the user does so manually. If the pump is already running
due to a filter cycle running or the spa is heating between filter cycles,
it will already be running on low speed. Depressing the pump 1 key
will then switch the pump to high speed. A second pressing of the
The Pump 1 symbol will appear in the LCD window 
when the Pump 1 is running at high speed. The symbol will blink
when the pump is running at low speed.
PUMP 2 KEY: Pump 2 is a two speed, the
Pump 2 key is used to turn it on ad to select between off, Low and high speeds.
A built-in timer will shut the pump off 20 minutes after it has been started,
unless the user does so manually.
The Pump 2 symbol will appear in the LCD window 
when the Pump 2 is running at high speed. The symbol will blink when the
pump is running at low speed.
The appearance of the Set Point symbol
in the LCD window tells the user that the temperature shown is the desired,
and not the actual temperature of the water. The temperature can be adjusted
in 1° F increments. The display will
always revert to the actual water temperature after you release the keys
for 5 seconds.
WATER HEATER AUTOMATIC START: When the water temperature is 1° F lower than the set point the pump (at low speed if it is a two speed pump) and the heater will be turned on until the water temperature reaches the set pint plus 1° F. The low speed pump will come on and run anytime the spa temperature controller calls for heat.
The heater symbol
will appear in the LCD window when the heater is on. The Heater On
symbol will blink in the LCD window whenever there is a call for heat and
the heater has not yet turned on.
AIR PUMP KEY:
This key is used to turn a blower on or off. If the blower is a two-speed blower the first press will turn the blower to high speed, the second press will turn the blower to low speed, the third press will turn the blower off. A built in timer will shut the blower off after 20 minutes, unless it is shut off manually. The Accessory/List key may be used for advanced programming functions.
When the Air Pump is on the air symbol
will appear in the LCD window ( it will blink if the speed is at low).
LIGHT KEY: The light key is used to turn the
light on or off and to select light intensities. The first press of the Light
Key will turn the light on at its highest intensity. A second press will
change the light intensity from high to low intensity (If multiple intensities
are available) A third press will turn the light off. The light will automatically
turn itself off after 2 hours.
When the light is on the light symbol 
will appear in the LCD window (it will blink if the intensity is at low).
PROGRAM KEY: The Program key is used to switch
between normal and programming modes. Pressing and holding this key
enters the programming mode. See "Programming" on back.
The program mode symbol will not appear in the LCD window when the unit is in programming mode. Refer to the programming section for more details.
TEMPERATURE DISPLAY: In Normal Mode operation,
the display shows actual water temperature.
SUMMARY OF LCD WINDOW CODES:
FrEE Freeze Protection Alarm
FLC Pressure Switch Alarm
HL High Temperature Alert
Prr Temperature Sensors Alarm.
F See hours of filtration
FLO Pressure Switch Alarm
PrH Temperature Sensors alarm.
Any of theses codes may be replaced in your controller with flashing dots
and or flashing numerals in the digital display.
For any of the above system error indicators do the following:
At anytime you get an error code, make
sure the water level is correct, the spa has the jets in the on position.
If you see water flowing normally on low speed, and the water level
is correct, then remove the filter(s) to see if the error code goes away.
Check the condition of the filters. If the problem is solved
by removing the filter, then the filters are too dirty to allow proper water
flow. The heater will not work without enough water available to the
pump.
If you get an error code and the pump is not running when it should be
on, check the fuses on the circuit board. If you are not familiar
with this procedure call 1-888-478-2224. NEVER PLACE YOUR HAND INSIDE
THE CONTROL BOX WHILE THE ELECTRICITY IS POWERED ON.
PROGRAMMING THE FILTER CYCLES:
Depress the program key. The display will change from the
temperature display to "F XX" The desired filter times can be adjusted
by depressing the up and down keys until the filter times are set. For
instance if you want to set the filter times to 4 hours twice a day at a
12 hour interval, depress the program key for five seconds then set the
display with the up and down keys to read: "F 04". To set the start
time for the 12 hour interval, simply depress the program key a second time
and the filter cycle will start at that time. We recommend starting
at 5, 6, 7 AM or PM for four hours standard. If you have an auauxiliarySC
Ozone) 24 hour pump, you only need to set it for 1 or 2 hours.
The economy key is used to set the spa into economy mode. You simply
depress the key until you see the economy symbol
in the display . When the economy key is set and the symbol is
displayed the temperature setting will be automatically set at 20 degrees
below the set point. We do not recommend using the Economy Mode in
winter.